The mesh belt ultrasonic spray cleaning machine is widely used in the through type ultrasonic spray cleaning and drying line. Many people do not know its work flow. The mesh belt ultrasonic spray cleaning machine produced by gutehong industry can effectively remove oil, wax, rust and dirt. It has the functions of cleaning, rinsing and drying.

網帶式超聲波噴淋清洗機工藝流程：投料→ 超聲波去污（28KHZ）→ 超聲波清洗（40K）→ 清水或純水（鼓泡）→ 風吹→ 下料

Technological process of mesh belt ultrasonic spray cleaning machine: feeding → ultrasonic decontamination (28kHz) → ultrasonic cleaning (40K) → clean water or pure water (bubbling) → wind blowing → blanking

網帶式超聲波噴淋清洗機由超聲波清洗系統、箱體室、罐體加熱系統、輸送鏈及傳動系統、壓縮空氣干燥系統、油水分離器、自動刮油機、電氣控制系統等組成.

The mesh belt ultrasonic spray cleaning machine is composed of ultrasonic cleaning system, box chamber, tank heating system, conveying chain and transmission system, compressed air drying system, oil-water separator, automatic oil scraper, electrical control system, etc

網帶式超聲波噴淋清洗機為鏈條網帶通超型超聲波清洗漂洗機。采用專用鏈條傳動輸送工件，具有清洗、漂洗、吹水等功能。將工件手動放置在傳動鏈的網帶上，然后通過通超聲波清洗室、超聲波清洗室、鼓泡清洗室和噴水室。清洗、漂洗、干燥等工序完成后，物料排出。清洗液經凈化處理后可循環使用，上罩內的水霧經抽風機抽出后排放主排氣管。該機具有多工位、功能齊全、結構合理、操作方便、清洗效果好等優點，對流水線零件的清洗、改善工作環境、提高清洗干燥質量具有重要意義。、

The mesh belt ultrasonic spray cleaning machine is a chain mesh belt through ultrasonic cleaning and rinsing machine. The special chain transmission is adopted to transport the workpiece, which has the functions of cleaning, rinsing, water blowing and so on. Place the workpiece on the mesh belt of the transmission chain manually, and then pass through the ultrasonic cleaning room, ultrasonic cleaning room, bubble cleaning room and water spraying room. After the cleaning, rinsing, drying and other processes are completed, the materials are discharged. The cleaning solution can be recycled after purification. The water mist in the upper cover is pumped out by the exhaust fan and then discharged to the main exhaust pipe. The machine has the advantages of multi station, complete functions, reasonable structure, convenient operation and good cleaning effect. It is of great significance to clean convective waterline parts, improve working environment and improve cleaning and drying quality.

網帶采用專用不銹鋼網帶。由于工件較重，采用三鏈形式，保證每平方分米軸承壓力不低于20kg。工件用專用夾具固定在網帶上，保證無滑動、無接觸、易清潔.

The mesh belt adopts special stainless steel mesh belt. Because the workpiece is heavy, the three chain form is adopted to ensure that the bearing pressure per square decimeter is not less than 20kg. The workpiece is fixed on the mesh belt with special fixture to ensure no sliding, no contact and easy cleaning

調速面板配有：轉速表、電源開關、指示燈、保險絲、表盤、調速旋鈕。使用時應先啟動輸送電機；然后將速度控制器電源開關置于“on（通）”位置，指示燈亮；輕輕轉動調速旋鈕，即可改變調速電機的轉速：順時針方向轉速升高，逆時針方向轉速降低；然后按下轉速表以穩定所需的速度。停機時，先將調速控制器電源開關置于“off”位置；2-3分鐘后關閉輸送電機。

The speed regulating panel is equipped with: tachometer, power switch, indicator light, fuse, dial and speed regulating knob. When using, start the conveying motor first; Then turn the power switch of the speed controller to the "on" position, and the indicator light is on; Gently turn the speed regulating knob to change the speed of the speed regulating motor: the speed increases in the clockwise direction and decreases in the counterclockwise direction; Then press the tachometer in order to stabilize the desired speed. During shutdown, first set the power switch of the speed controller to the "off" position; Turn off the conveying motor after 2-3 minutes.